Audio/Video Transport M. Hatanaka
Internet-Draft J. Matsumoto
Expires: October 23, 2009 Sony Corporation
April, 2009
RTP Payload Format for Adaptive TRansform Acoustic Coding (ATRAC) Family
draft-ietf-avt-rtp-atrac-family-22
Status of this Memo
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on October 23, 2009.
Submission Compliance for Internet-Drafts
This Internet-Draft is submitted to IETF in full conformance with
the provisions of BCP 78 and BCP 79.
Copyright and License Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
Hatanaka, et al. [Page 1]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
Abstract
This document describes an RTP payload format for efficient and
flexible transporting of audio data encoded with the Adaptive
TRansform Audio Coding (ATRAC) family of codecs. Recent enhancements
to the ATRAC family of codecs support high quality audio coding with
multiple channels. The RTP payload format as presented in this
document also includes support for data fragmentation, elementary
redundancy measures, and a variation on scalable streaming.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Conventions Used in This Document . . . . . . . . . . . . . . 4
3. Codec Specific Details . . . . . . . . . . . . . . . . . . . . 4
4. RTP Packetization and Transport of ATRAC-Family Streams . . . 5
4.1 ATRAC Frames . . . . . . . . . . . . . . . . . . . . . . . 5
4.2 Concatenation of Frames . . . . . . . . . . . . . . . . . 5
4.3 Frame Fragmentation . . . . . . . . . . . . . . . . . . . 5
4.4 Transmission of Redundant Frames . . . . . . . . . . . . . 6
4.5 Scalable Lossless Streaming (High-Speed Transfer mode) . . 6
4.5.1 Scalable Multiplexed Streaming . . . . . . . . . . . . 6
4.5.2 Scalable Multi-Session Streaming . . . . . . . . . . . 7
5. Payload Format . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1 Global Structure of Payload Format . . . . . . . . . . . . 8
5.2 Usage of RTP Header Fields . . . . . . . . . . . . . . . . 9
5.3 RTP Payload Structure . . . . . . . . . . . . . . . . . . 10
5.3.1 ATRAC Header Section . . . . . . . . . . . . . . . . . 10
5.3.2 ATRAC Frames Section . . . . . . . . . . . . . . . . . 11
5.3.2.1 Support of redundancy. . . . . . . . . . . . . . . . . 11
5.3.2.2 Frame Fragmentation . . . . . . . . . . . . . . . . . 13
6. Packetization Examples . . . . . . . . . . . . . . . . . . . . 14
6.1 Example Multi-frame Packet . . . . . . . . . . . . . . . . 14
6.2 Example Fragmented ATRAC Frame . . . . . . . . . . . . . . 15
7. Payload Format Parameters . . . . . . . . . . . . . . . . . . 16
7.1 ATRAC3 Media type Registration . . . . . . . . . . . . . . 17
7.2 ATRAC-X Media type Registraion . . . . . . . . . . . . . . 19
7.3 ATRAC Advanced Lossless Media type Registration . . . . . 21
7.4 Channel Mapping Configuration Table . . . . . . . . . . . 23
7.5 Mapping Media type Parameters into SDP . . . . . . . . . . 24
7.5.1 For Media subtype ATRAC3 . . . . . . . . . .. . . . . 24
7.5.2 For Media subtype ATRAC-X . . . . . . . . . .. . . . . 24
7.5.3 For Media subtype ATRAC Advanced Lossless . .. . . . . 25
7.6 Offer-Answer Model Considerations . . . . . . . . . . . . 26
7.6.1 For All Three Media Subtypes . . . . . . . .. . . . . 26
7.6.2 For Media subtype ATRAC3 . . . . . . . . . . . . . . 26
7.6.3 For Media subtype ATRAC-X . . . . . . . . . . . . . . 27
7.6.4 For Media subtype ATRAC Advanced Lossless . . . . . . 27
7.7 Usage of declarative SDP . . . . . . . . . . . . . . . . . 28
7.8 Example SDP Session Descriptions . . . . . . . . . . . . . 28
7.9 Example Offer-Answer Exchange . . . . . . . . . . . . . . 30
Hatanaka, et al. [Page 2]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 32
9. Security Considerations . . . . . . . . . . . . . . . . . . . 32
10. Considerations on Correct Decoding . . . . . . . . . . . . . . 33
10.1 Verification of the Packets . . . . . . . . . . . . . . . 33
10.2 Validity Checking of the Packets . . . . . . . . . . . . . 33
11. References . . . . . . . . . . . . . . . . . . . . . . . . . 34
11.1 Normative References . . . . . . . . . . . . . . . . . . . 34
11.2 Informative References . . . . . . . . . . . . . . . . . . 35
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 35
Intellectual Property and Copyright Statements . . . . . . . . 36
Hatanaka, et al. [Page 3]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
1. Introduction
The ATRAC family of perceptual audio codecs is designed to address
numerous needs for high-quality, low bit-rate audio transfer. ATRAC
technology can be found in many consumer and professional products
and applications, including MD players, CD players, voice recorders,
and mobile phones.
Recent advances in ATRAC technology allow for multiple channels of
audio to be encoded in customizable groupings. This should allow
for future expansions in scaled streaming. To provide the greatest
flexibility in streaming any one of the ATRAC family member codecs,
however, this payload format does not distinguish between the codecs
on a packet level.
This simplified payload format contains only the basic information
needed to disassemble a packet of ATRAC audio in order to decode it.
There is also basic support for fragmentation and redundancy.
2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC2119 [4].
3. Codec Specific Details
Early versions of the ATRAC codec handled only two channels of audio
at 44.1kHz sampling frequency, with typical bit-rates between 66kbps
and 132kbps. The latest version allows for a maximum 8 channels of
audio, up to 96kHz in sampling frequency, and a lossless encoding
option which can be transmitted in either a scalable (also known as
High-Speed Transfer mode) or standard (aka Standard mode) format.
The feasible bit-rate range has also expanded, allowing from a low of
8kbps up to 1400kbps in lossy encoding modes.
Depending on the version of ATRAC used, the sample-frame size is
either 512, 1024 or 2048 samples. While the lossy and Standard mode
lossless formats are encoded as sequential single audio frames,
High-Speed Transfer mode lossless data comprises two layers -- a
lossy base layer and an enhancement layer.
Although streaming of multi-channel audio is supported depending on
the ATRAC version used, all encoded audio for a given time period is
contained within a single frame. Therefore, there is no interleaving
nor splitting of audio data on a per-channel basis to be concerned
with.
Hatanaka, et al. [Page 4]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
4. RTP Packetization and Transport of ATRAC-Family Streams
4.1 ATRAC Frames
For transportation of compressed audio data, ATRAC uses the concept
of frames. ATRAC frames are the smallest data unit for which timing
information is attributed. Frames are octet-aligned by definition.
4.2 Concatenation of Frames
It is often possible to carry multiple frames in one RTP packet.
This can be useful in audio, where on a LAN with a 1500 byte MTU, an
average of 7 complete 64kbps ATRAC frames could be carried in a
single RTP packet, as each ATRAC frame would be approximately 200
bytes. ATRAC frames may be of fixed or variable length. To
facilitate parsing in the case of multiple frames in one RTP packet,
the size of each frame is made known to the receiver by carrying "in
band" the frame size for each contained frame in an RTP packet.
However, to simplify the implementation of RTP receivers, it is
required that when multiple frames are carried in an RTP packet, each
frame MUST be complete, i.e., the number of frames in an RTP packet
MUST be integral.
4.3 Frame Fragmentation
The ATRAC codec can handle very large frames. As most IP networks
have significantly smaller MTU sizes than the frame sizes ATRAC can
handle, this payload format allows for the fragmentation of an ATRAC
frame over multiple RTP packets. However, to simplify the
implementation of RTP receivers, an RTP packet MUST either carry one
or more complete ATRAC frames or a single fragment of one ATRAC
frame. In other words, RTP packets MUST NOT contain fragments of
multiple ATRAC frames and MUST NOT contain a mix of complete and
fragmented frames.
Hatanaka, et al. [Page 5]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
4.4 Transmission of Redundant Frames
As RTP does not guarantee reliable transmission, receipt of data is
not assured. Loss of a packet can result in a "decoding gap" at the
receiver. One method to remedy this problem is to allow time-shifted
copies of ATRAC frames to be sent along with current data. For a
modest cost in latency and implementation complexity, error
resiliency to packet loss can be achieved. For further details, see
section 5.3.2.1, and reference[12].
4.5 Scalable Lossless Streaming (High-Speed Transfer mode)
As ATRAC supports a variation on scalable encoding, this payload
format provides a mechanism for transmitting essential data (also
referred to as the base layer) with its enhancement data in two ways
-- multiplexed through one session or separated over two sessions.
In either method, only the base layer is essential in producing audio
data. The enhancement layer carries the remaining audio data needed
to decode lossless audio data. So in situations of limited
bandwidth, the sender may choose not to transmit enhancement data yet
still provide a client with enough data to generate lossily-encoded
audio through the base layer.
4.5.1 Scalable Multiplexed Streaming
In multiplexed streaming, the base layer and enhancement layer are
coupled together in each packet, utilizing only one session as
illustrated in Figure 1.
The packet MUST begin with base layer, and the two layer types
MUST interleave if both of layer exist in a packet (only base or
enhancement is included in a packet at the beginning of a streaming,
or during the fragmentation).
+----------------+ +----------------+ +----------------+
|Base|Enhancement|--|Base|Enhancement|--|Base|Enhancement| ...
+----------------+ +----------------+ +----------------+
N N+1 N+2 : Packet
Figure 1. Multiplexed structure
Hatanaka, et al. [Page 6]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
4.5.2 Scalable Multi-Session Streaming
In multi-session streaming, the base layer and enhancement layer are
sent over two separate sessions, allowing clients with certain
bandwidth limitations to receive just the base layer for decoding as
illustrated in Figure 2.
In this case, it is REQUIRED to determine which sessions are paired
together in receiver side. For paired base and enhancement layer
session, the CNAME bindings in RTCP session MUST be applied using the
same CNAME to ensure correct mapping to the RTP source.
While there may be alternative methods for synchronization of the
layers, the timestamp SHOULD be used for synchronizing the base layer
with its enhancement. The two sessions MUST be synchronized
using the information in RTCP SR packets to align the RTP timestamps.
If the enhancement layer's session data cannot arrive until
the presentation time, the decoder MUST decode the Base layer
session's data only, ignoring the enhancement layer's data.
Session 1:
+------+ +------+ +------+ +------+
| Base |--| Base |--| Base |--| Base | ...
+------+ +------+ +------+ +------+
N N+1 N+2 N+3 : Packet
Session 2:
+-------------+ +-------------+ +-------------+
| Enhancement |--| Enhancement |--| Enhancement | ...
+-------------+ +-------------+ +-------------+
N N+1 N+2 : Packet
Figure 2. Multi-Session Streaming
Hatanaka, et al. [Page 7]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
5. Payload Format
5.1 Global Structure of Payload Format
The structure of ATRAC Payload is illustrated in Figure 3.
The RTP payload following the RTP header contains two
octet-aligned data sections.
+------+--------------+-----------------------------+
|RTP | ATRAC Header | ATRAC Frames Section |
|Header| Section | (including redundant data) |
+------+--------------+-----------------------------+
< ---------------- RTP Packet Payload ------------- >
Figure 3. Structure of RTP Payload of ATRAC family
The first data section is the ATRAC Header, containing just one
header with information for the whole packet. The second
section is where the encoded ATRAC frames are stored. This may
contain either a single fragment of one ATRAC frame, or one or more
complete ATRAC frames. The ATRAC Frames Section MUST NOT be empty.
When using the redundancy mechanism described in section 5.3.2.1, the
redundant frame data can be included in this section and time stamp
MUST be set to the oldest redundant frame's time stamp.
To benefit from ATRAC's High-Speed Transfer mode lossless encoding
capability, the RTP payload can be split across two sessions, with
one transmitting an essential base layer and the other transmitting
enhancement data. However in either case, the above structure still
applies.
Hatanaka, et al. [Page 8]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
5.2 Usage of RTP Header Fields
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P|X| CC |M| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| contributing source (CSRC) identifiers |
| ..... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4. RTP Standard Header Part
The structure of RTP Standard Header Part is illustrated in Figure 4.
Version(V): 2 bits
Set to 2.
Padding(P): 1 bit
If the padding bit is set, the packet contains one or more
additional padding octets at the end which are not part of the
payload. The last octet of the padding contains a count of how
many padding octets should be ignored, including itself. Padding
may be needed by some encryption algorithms with fixed block sizes
or for carrying several RTP packets in a lower-layer protocol data
unit (see [1]).
Extension(X): 1 bit
Defined by the RTP profile used.
CSRC count(CC): 4bits
see RFC 3550[1].
Marker (M): 1 bit
Set to 1 if the packet is the first packet after a silence period,
otherwise it MUST be set to 0.
Payload Type (PT): 7 bits
The assignment of an RTP payload type for this packet format is
outside the scope of this document; it is specified by the RTP
profile under which this payload format is used, or signaled
dynamically out-of-band (e.g., using SDP).
Hatanaka, et al. [Page 9]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
sequence number: 16bits
A sequential number for RTP packet. It ranges from 0 to 65535 and
repeats itself periodically.
Timestamp: 32 bits
A timestamp representing the sampling time of the first sample of
the first ATRAC frame in the current RTP packet.
When using SDP, the clock rate of the RTP timestamp MUST be
expressed using the "rtpmap" attribute.
For ATRAC3 and ATRAC Advanced Lossless, the RTP timestamp rate
MUST be 44100Hz. For ATRAC-X the RTP timestamp rate is 44100Hz or
48000Hz, and it will be selected by out-of-band signaling.
SSRC: 32bits
see RFC 3550[1].
CSRC list: 0 to 15 items, 32bits each
see RFC 3550[1].
5.3 RTP Payload Structure
5.3.1 Usage of ATRAC Header Section
The ATRAC header section has the fixed length of one byte as
illustrated in Figure 5.
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|C|FrgNo|NFrames|
+-+-+-+-+-+-+-+-+
Figure 5. ATRAC RTP Header
Continuation Flag (C) : 1bit
The packet which corresponds to the last part of the audio frame data
in a fragmentation, MUST have this bit to 0, otherwise set to 1.
Fragment Number (FrgNo): 3 bits
In the event of data fragmentation, this value is one for the first
packet, and increases sequentially for the remaining fragmented data
packets. This value MUST be zero for an unfragmented frame. (Note:
3 bits is sufficient to avoid Fragment Number rollover given the
current maximum supported bit-rate in the ATRAC specification. If
that changes, the choice of 3 bits for the Fragment Number should be
revisited.)
Number of Frames (NFrames): 4 bits
The number of audio frames in this packet are field value + 1.
This allows for a maximum of 16 ATRAC-encoded audio frames per
packet, with 0 indicating one audio frame. Each audio frame MUST be
complete in the packet if fragmentation is not applied. In case of
fragmentation, the data for only one audio frame is allowed to be
fragmented, and this value MUST be 0.
Hatanaka, et al. [Page 10]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
5.3.2 Usage of ATRAC Frames Section
The ATRAC Frames Section contains an integer number of complete
ATRAC frames or a single fragment of one ATRAC frame as
illustrated in Figure 6. Each ATRAC frame is preceded by a one-bit
flag indicating the layer type and a Block Length field indicating
the size in bytes of the ATRAC frame. If more than one ATRAC frame
is present, then the frames are concatenated into a contiguous
string of bit-flag, Block Length, and ATRAC frame in order of their
frame number. This section MUST NOT be empty.
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|E| Block Length | ATRAC frame |...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6. ATRAC Frame Section Format
Layer Type Flag (E): 1 bit
Set to 1 if the corresponding ATRAC frame is from an enhancement
layer. 0 indicates a base layer encoded frame.
Block length: 15 bits
The byte length of encoded audio data for the following frame. This
is so that in the case of fragmentation, if only a subsequent packet
is received, decoding can still occur. 15 bits allows for a maximum
block length of 32,767 bytes.
ATRAC frame: The encoded ATRAC audio data.
5.3.2.1 Support of redundancy
This payload format provides a rudimentary scheme to compensate
for occasional packet loss. As every packet's timestamp corresponds
to the first audio frame regardless of whether it is redundant or
not, and because we know how many frames of audio each packet
encapsulates, if two successive packets are successfully transmitted,
we can calculate the number of redundant frames being sent. The
result gives the client a sense of how the server is responding to
RTCP reports and warns it to expand its buffer size if necessary.
As an example of using the Redundant Data, refer to Figure 7 and 8.
In this example, the server has determined that for the next few
number of packets, it should send the last two frames from the
previous packet due to recent RTCP reports. Thus, between packets
N and N+1, there is a redundancy of two frames (which the client
may choose to dispose of). The benefit arises when packets N+2
and N+3 do not arrive at all, after which eventually packet N+4
arrives with successive necessary audio frame data.
Hatanaka, et al. [Page 11]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
[Sender]
|-Fr0-|-Fr1-|-Fr2-| Packet: N, TS=0
|-Fr1-|-Fr2-|-Fr3-| Packet: N+1, TS=1024
|-Fr2-|-Fr3-|-Fr4-| Packet: N+2, TS=2048
|-Fr3-|-Fr4-|-Fr5-| Packet: N+3, TS=3072
|-Fr4-|-Fr5-|-Fr6-| Packet: N+4, TS=4096
-----------> Packet "N+2" and "N+3" not arrived ------------->
[Receiver]
|-Fr0-|-Fr1-|-Fr2-| Packet: N, TS=0
|-Fr1-|-Fr2-|-Fr3-| Packet: N+1, TS=1024
|-Fr4-|-Fr5-|-Fr6-| Packet: N+4, TS=4096
The receiver can decode from FR4 to Fr6 by using Packet "N+4" data
even if the packet loss of "N+2" and "N+3" is occured.
Figure 7. Redundant Example
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P|X| CC |M| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp (= start sample time of Fr1) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| contributing source (CSRC) identifiers |
| ..... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| 0 | 3 |0| Block Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (redundant) ATRAC frame (Fr1) data ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| Block Length |(redundant) ATRAC frame (Fr2) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (cont.) |0| Block Length | ATRAC frame (Fr3) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (cont.) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 8. Packet structure example with Redundant data
(case of Packet "N+1")
Hatanaka, et al. [Page 12]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
5.3.2.2 Frame Fragmentation
Each RTP packet MUST contain either an integer number of ATRAC
encoded audio frames (with a maximum of 16), or one ATRAC frame
fragment. In the former case, as many complete ATRAC frames as can
fit in a single path-MTU SHOULD be placed in an RTP packet. However,
if even a single ATRAC frame will not fit into a complete RTP packet,
the ATRAC frame MUST be fragmented.
The start of a fragmented frame gets placed in its own RTP packet
with its Continuation bit (C) set to one, and its Fragment Number
(FragNo) set to one. As the frame must be the only one in the
packet, the Number of Frames field is zero. Subsequent packets are
to contain the remaining fragmented frame data, with the Fragment
Number increasing sequentially and the Continuation bit (C)
consistently set to one. As subsequent packets do not contain any new
frames, the Number of Frames field MUST be ignored. The last packet
of fragmented data MUST have the Continuation bit (C) set to zero.
Packets containing related fragmented frames MUST have identical
timestamps. Thus, while the Continuous bit and Fragment Number fields
indicate fragmentation and a means to reorder the packets, the
timestamp can be used to determine which packets go together."
Hatanaka, et al. [Page 13]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
6. Packetization Examples
6.1 Example Multi-frame Packet
Multiple encoded audio frames are combined into one packet. Note
how for this example, only base layer frames are sent redundantly,
but are followed by interleaved base layer and enhancement layer
frames as illustrated in Figure 9.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P|X| CC |M| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| contributing source (CSRC) identifiers |
| ..... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| 0 | 5 |0| Block Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (redundant) base layer frame 1 data... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| Block Length |(redundant) base layer frame 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (cont.) |0| Block Length | base layer frame 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (cont.) |1| Block Length | enhancement frame 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (cont.) |0| Block Length | base layer frame 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (cont.) |1| Block Length | enhancement frame 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 9. Example Multi-frame Packet
Hatanaka, et al. [Page 14]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
6.2 Example Fragmented ATRAC Frame
The encoded audio data frame is split over three RTP packets as
illustrated in Figure 10. The following points are highlighted
in the example below:
o transition from one to zero of the Continuation bit (C)
o sequential increase in the Fragment Number
Packet 1:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P|X| CC |M| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| contributing source (CSRC) identifiers |
| ..... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| 1 | 0 |1| Block Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| enhancement data... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Packet 2:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P|X| CC |M| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| contributing source (CSRC) identifiers |
| ..... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| 2 | 0 |1| Block Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...more enhancement data... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Hatanaka, et al. [Page 15]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
Packet 3:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P|X| CC |M| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| contributing source (CSRC) identifiers |
| ..... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| 3 | 0 |1| Block Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...the last of the enhancement data |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 10. Example Fragmented ATRAC Frame
7. Payload Format Parameters
Certain parameters will need to be defined before ATRAC family
encoded content can be streamed. Other optional parameters may also
be defined to take advantage of specific features relevant to certain
ATRAC versions. Parameters for ATRAC3, ATRAC-X, and ATRAC Advanced
Lossless are defined here as part of the media subtype registration
process. A mapping of these parameters into the Session Description
Protocol (SDP) (RFC 4566) [2] is also provided for applications that
utilize SDP. These registrations use the template defined in RFC
4288 [5] and follow RFC 4855 [6].
The data format and parameters are specified for real-time transport
in RTP.
Hatanaka, et al. [Page 16]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.1 ATRAC3 Media type Registration
The media subtype for the Adaptive TRansform Codec version 3 (ATRAC3)
uses the template defined in RFC 4855 [6].
Note, any unknown parameter MUST be ignored by the receiver.
Type name: audio
Subtype name: atrac3
Required parameters:
rate: Represents the sampling frequency in Hz of the original
audio data. Permissible value is 44100 only.
baseLayer: Indicates the encoded bit-rate in kbps for the audio
data to be streamed. Permissible values are 66, 105 and 132.
Optional parameters:
ptime: see RFC4566[2]
maxptime: see RFC4566[2]
The frame length of ATRAC3 is 1024/44100 = 23.22...(ms), and
fractional value may not be applicable for the SDP definition.
So the the value of the parameter MUST be a multiple of 24(ms)
considering safe transmission.
If this parameter is not present, the sender MAY encapsulate
a maximum of 6 encoded frames into one RTP packet, in streaming
of ATRAC3.
maxRedundantFrames: The maximum number of redundant frames that may
be sent during a session in any given packet under the redundant
framing mechanism detailed in the draft. Allowed values are integers
in the range of 0 to 15, inclusive. If this parameter is not used, a
default of 15 MUST be assumed.
Encoding considerations: This media type is framed and contains
binary data.
Security considerations: This media type does not carry active
content. See Section 9 of this document.
Interoperability considerations: none
Published specification: ATRAC3 Standard Specification[9]
Hatanaka, et al. [Page 17]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
Applications that use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Magic number(s): none
File extension(s): 'at3', 'aa3', and 'omg'
Macintosh file type code(s): none
Person & email address to contact for further information:
Mitsuyuki Hatanaka
Jun Matsumoto
actech@jp.sony.com
Intended usage: COMMON
Restrictions on usage: This media type depends on RTP framing,
and hence is only defined for transfer via RTP.
Author:
Mitsuyuki Hatanaka
Jun Matsumoto
actech@jp.sony.com
Change controller: IETF AVT WG delegated from the IESG
Hatanaka, et al. [Page 18]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.2 ATRAC-X Media type Registration
The media subtype for the Adaptive TRansform Codec version X
(ATRAC-X) uses the template defined in RFC 4855 [6].
Note, any unknown parameter MUST be ignored by the receiver.
Type name: audio
Subtype name: atrac-x
Required parameters:
rate: Represents the sampling frequency in Hz of the original
audio data. Permissible values are 44100 and 48000.
baseLayer: Indicates the encoded bit-rate in kbps for the audio
data to be streamed. Permissible values are 32, 48, 64, 96, 128,
160, 192, 256, 320 and 352.
channelID: Indicates the number of channels and channel layout
according to the table1 in Section 7.4. Note that this layout is
different from that proposed in RFC 3551 [3]. However, as
channelID = 0 defines an ambiguous channel layout, the channel
mapping defined in Section 4.1 of [3] could be used. Permissible
values are 0, 1, 2, 3, 4, 5, 6, 7.
Optional parameters:
ptime: see RFC4566[2]
maxptime: see RFC4566[2]
The frame length of ATRAC-X is 2048/44100 = 46.44...(ms) or
2048/48000 = 42.67...(ms), but fractional value may not be applicable
for the SDP definition. So the value of the parameter MUST be a
multiple of 47(ms) or 43(ms) considering safe transmission.
Hatanaka, et al. [Page 19]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
If this parameter is not present, the sender MAY encapsulate a
maximum of 16 encoded frames into one RTP packet, in streaming
of ATRAC-X.
maxRedundantFrames: The maximum number of redundant frames that
may be sent during a session in any given packet under the redundant
framing mechanism detailed in the draft. Allowed values are integers
in the range 0 to 15, inclusive. If this parameter is not used, a
default of 15 MUST be assumed.
delayMode: Indicates a desire to use low-delay features, in which
case the decoder will process received data accordingly based on
this value. Permissible values are 2 and 4.
Encoding considerations: This media type is framed and contains
binary data.
Security considerations: This media type does not carry active
content. See Section 9 of this document.
Interoperability considerations: none
Published specification: ATRAC-X Standard Specification[10]
Applications that use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Magic number(s): none
File extension(s): 'atx', 'aa3', and 'omg'
Macintosh file type code(s): none
Person & email address to contact for further information:
Mitsuyuki Hatanaka
Jun Matsumoto
actech@jp.sony.com
Intended usage: COMMON
Restrictions on usage: This media type depends on RTP framing,
and hence is only defined for transfer via RTP.
Author:
Mitsuyuki Hatanaka
Jun Matsumoto
actech@jp.sony.com
Change controller: IETF AVT WG delegated from the IESG
Hatanaka, et al. [Page 20]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.3 ATRAC Advanced Lossless Media type Registration
The media subtype for the Adaptive TRansform Codec Lossless version
(ATRAC Advanced Lossless) uses the template defined in RFC 4855 [6].
Note, any unknown parameter MUST be ignored by the receiver.
Type name: audio
Subtype name: atrac-advanced-lossless
Required parameters:
rate: Represents the sampling frequency in Hz of the original
audio data. Permissible value is 44100 only for High-speed transfer
mode. Any value of 24000, 32000, 44100, 48000, 64000, 88200,
96000, 176400 and 192000 can be used for Standard mode.
baseLayer: Indicates the encoded bit-rate in kbps for the base
layer in High-Speed Transfer mode lossless encodings.
For Standard lossless mode this value MUST be 0.
The Permissible values for ATRAC3 baselayer are 66, 105 and 132.
For ATRAC-X baselayer, they are 32, 48, 64, 96, 128, 160, 192, 256,
320 and 352.
blockLength: Indicates the block length. In High-speed Transfer
mode, the value of 1024 and 2048 is used for ATRAC3 and ATRAC-X
based ATRAC Advanced Lossless streaming, respectively.
Any value of 512, 1024 and 2048 can be used for Standard mode.
channelID: Indicates the number of channels and channel layout
according to the table1 in Section 7.4. Note that this layout is
different from that proposed in RFC 3551 [3]. However, as channelID
= 0 defines an ambiguous channel layout, the channel mapping defined
in Section 4.1 of [3] could be used in this case. Permissible values
are 0, 1, 2, 3, 4, 5, 6, 7.
ptime: see RFC4566[2]
maxptime: see RFC4566[2]
In streaming of ATRAC Advanced Lossless, multiple frames cannot be
transmitted in a single RTP packet, as the frame size is large.
So it SHOULD be regarded as the time of one encoded frame in both of
the sender and the receiver side. The frame length of ATRAC Advanced
Lossless is 512/44100 = 11.6...(ms), 1024/44100 = 23.22...(ms) or
2048/44100 = 46.44...(ms), but fractional value may not be applicable
for the SDP definition. So the the value of the parameter MUST be
12(ms), 24(ms) or 47(ms) considering safe transmission.
Encoding considerations: This media type is framed and contains
binary data.
Hatanaka, et al. [Page 21]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
Security considerations: This media type does not carry active
content. See Section 9 of this document.
Interoperability considerations: none
Published specification:
ATRAC Advanced Lossless Standard Specification[11]
Applications that use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Magic number(s): none
File extension(s): 'aal', 'aa3', and 'omg'
Macintosh file type code(s): none
Person & email address to contact for further information:
Mitsuyuki Hatanaka
Jun Matsumoto
actech@jp.sony.com
Intended usage: COMMON
Restrictions on usage: This media type depends on RTP framing,
and hence is only defined for transfer via RTP.
Author:
Mitsuyuki Hatanaka
Jun Matsumoto
actech@jp.sony.com
Change controller: IETF AVT WG delegated from the IESG
Hatanaka, et al. [Page 22]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.4 Channel Mapping Configuration Table
The Table 1 explains the mapping between the channelID as
passed during SDP negotiations, and the speaker mapping the
value represents.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| channelID | Number of | Default Speaker |
| | Channels | Mapping |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0 | max 64 | undefined |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 1 | 1 | front: center |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 2 | 2 | front: left, right |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 3 | 3 | front: left, right |
| | | front: center |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 4 | 4 | front: left, right |
| | | front: center |
| | | rear: surround |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5 | 5+1 | front: left, right |
| | | front: center |
| | | rear: left, right |
| | | LFE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 6 | 6+1 | front: left, right |
| | | front: center |
| | | rear: left, right |
| | | rear: center |
| | | LFE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 7 | 7+1 | front: left, right |
| | | front: center |
| | | rear: left, right |
| | | side: left, right |
| | | LFE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Table 1. Channel Configuration
Hatanaka, et al. [Page 23]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.5 Mapping Media type Parameters into SDP
The information carried in the Media type specification has a
specific mapping to fields in the Session Description Protocol (SDP)
[2], which is commonly used to describe RTP sessions. When SDP is
used to specify sessions employing the ATRAC family of codecs, the
following mapping rules according to the ATRAC codec apply:
7.5.1 For Media subtype ATRAC3
o The Media type ("audio") goes in SDP "m=" as the media name
o The Media subtype (payload format name) goes in SDP "a=rtpmap" as
the encoding name. ATRAC3 supports only mono or stereo signals,
so a corresponding number of channels(0 or 1) MUST also be
specified in this attribute.
o The "baseLayer" parameter goes in SDP "a=fmtp". This parameter
MUST be present. "maxRedundantFrames" may follow, but if no value
is transmitted, the receiver SHOULD assume a default value of
"15".
o The parameters "ptime" and "maxptime" go in the SDP "a=ptime" and
"a=maxptime" attributes, respectively.
7.5.2 For Media subtype ATRAC-X
o The Media type ("audio") goes in SDP "m=" as the media name
o The Media subtype (payload format name) goes in SDP "a=rtpmap" as
the encoding name. This SHOULD be followed by the "sampleRate"
(as the RTP clock rate), and then the actual number of channels
regardless of the channelID parameter.
o The parameters "ptime" and "maxptime" go in the SDP "a=ptime" and
"a=maxptime" attributes, respectively.
o Any remaining parameters go in the SDP "a=fmtp" attribute by
copying them directly from the Media type string as a
semicolon separated list of parameter=value pairs. The
"baseLayer" parameter MUST be the first entry on this line.
The "channelID" parameter MUST be the next entry. The receiver
MUST assume a default value of "15" for "maxRedundantFrames".
Hatanaka, et al. [Page 24]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.5.3 For Media subtype ATRAC Advanced Lossless
o The Media type ("audio") goes in SDP "m=" as the media name
o The Media subtype (payload format name) goes in SDP "a=rtpmap" as
the encoding name. This MUST be followed by the "sampleRate"
(as the RTP clock rate), and then the actual number of channels
regardless of the channelID parameter.
o The parameters "ptime" and "maxptime" go in the SDP "a=ptime" and
"a=maxptime" attributes, respectively.
o Any remaining parameters go in the SDP "a=fmtp" attribute by
copying them directly from the Media type string as a
semicolon separated list of parameter=value pairs.
On this line, the parameters "baseLayer" and "blockLength"
MUST be present in this order.
The value of "blockLength" MUST be one of 1024 and 2048, for
using ATRAC3 and ATRAC-X as baselayer, respectively.
If "baseLayer=0" (means standard mode), "blockLength" MUST be one
of either 512, 1024, or 2048. The "channelID" parameter MUST be
the next entry . The receiver MUST assume a default value of "15"
for "maxRedundantFrames".
Hatanaka, et al. [Page 25]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.6 Offer-Answer Model Considerations
Some options for encoding and decoding ATRAC audio data will require
either or both of the sender and receiver to comply with certain
specifications. In order to establish an interoperable transmission
framework, an Offer-Answer negotiation in SDP MUST observe the
following considerations. (See reference [14].):
7.6.1 For All Three Media Subtypes
o Each combination of the RTP payload transport format configuration
parameters (baseLayer and blockLength, sampleRate, channelID) is
unique in its bit-pattern and not compatible with any other
combination. When creating an offer in an application desiring to
use the more advanced features (sample rates above 44100kHz, more
than two channels), the offerer SHOULD also offer a payload type
containing only the lowest set of necessary requirements.
If multiple configurations are of interest to the application
they may all be offered.
o The parameters "maxptime" and "ptime" will in most cases not
affect interoperability, however the setting of the parameters can
affect the performance of the application. The SDP offer-answer
handling of the "ptime" parameter is described in RFC3264.
The "maxptime" parameter MUST be handled in the same way.
7.6.2 For Media subtype ATRAC3
o In response to an offer, downgraded subsets of "baseLayer" are
possible. However for best performance, we suggest the answer
contain the highest possible values offered.
Hatanaka, et al. [Page 26]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.6.3 For Media subtype ATRAC-X
o In response to an offer, downgraded subsets of "sampleRate",
"baseLayer", and "channelID" are possible. For best performance,
an answer MUST NOT contain any values requiring further
capabilities than the offer contains, but it SHOULD provide values
as close as possible to those in the offer.
o The "maxRedundantFrames" is a suggested minimum. This value MAY
be increased in an answer (with a maximum of 15), but MUST NOT be
reduced.
o The optional parameter "delayMode" is non-negotiable. If the
Answerer cannot comply with the offered value, the session MUST be
deemed inoperable.
7.6.4 For Media subtype ATRAC Advanced Lossless
o In response to an offer, downgraded subsets of "sampleRate",
"baseLayer", and "channelID" are possible. For best performance,
an answer MUST NOT contain any values requiring further
capabilities than the offer contains, but it SHOULD provide values
as close as possible to those in the offer.
o There are no requirements when negotiating "blockLength", other
than that both parties must be in agreement.
o The "maxRedundantFrames" is a suggested minimum. This value MAY
be increased in an answer (with a maximum of 15), but MUST NOT be
reduced.
o For transmission of scalable multi-session streaming of ATRAC
Advanced Lossless content, the attributes of media stream
identification, group information and decoding dependency between
base layer stream and enhancement layer stream MUST be signaled
in SDP by offer/answer model. In this case, the attribute of
"group", "mid" and "depend" followed by appropriate parameter MUST
be used in SDP[7][8] in order to indicate layered coding
dependency. The attribute of "group" followed by "DDP" parameter
is used for indicating relationship between the base and the
enhancement layer stream with decoding dependency. Each stream is
identified by "mid" attribute, and the dependency of enhancement
layer stream is defined by "depend" attribute, as the enhancement
layer is only useful when the base layer is available. Examples
for signaling ATRAC Advanced Lossless decoding dependency are
described in section 7.8 and 7.9.
Hatanaka, et al. [Page 27]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.7 Usage of declarative SDP
In declarative usage, like SDP in RTSP [15] or SAP [16], the
parameters MUST be interpreted as follows:
o The payload format configuration parameters (baseLayer,
sampleRate, channelID) are all declarative and a participant MUST
use the configuration(s) provided for the session. More than one
configuration may be provided if necessary by declaring multiple
RTP payload types, however the number of types SHOULD be kept
small.
o Any "maxptime" and "ptime" values SHOULD be selected with care to
ensure that the session's participants can achieve reasonable
performance.
o The attribute of "mid", "group" and "depend" MUST be used for
indicating relationship and dependency of the base layer and
the enhancement layer in scalable multi-session streaming of ATRAC
ADVANCED LOSSLESS content, as described in 7.6, 7.8 and 7.9.
7.8 Example SDP Session Descriptions
Example usage of ATRAC-X with stereo at 44100Hz:
v=0
o=atrac 2465317890 2465317890 IN IP4 service.example.com
s=ATRAC-X Streaming
c=IN IP4 192.0.2.1/127
t=3409539540 3409543140
m=audio 49120 RTP/AVP 99
a=rtpmap:99 ATRAC-X/44100/2
a=fmtp:99 baseLayer=128; channelID=2; delayMode=2
a=maxptime:47
Example usage of ATRAC-X with 5.1 setup at 48000Hz:
v=0
o=atrac 2465317890 2465317890 IN IP4 service.example.com
s=ATRAC-X 5.1ch Streaming
c=IN IP4 192.0.2.1/127
t=3409539540 3409543140
m=audio 49120 RTP/AVP 99
a=rtpmap:99 ATRAC-X/48000/6
a=fmtp:99 baseLayer=320; channelID=5
a=maxptime:43
Hatanaka, et al. [Page 28]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
Example usage of ATRAC-Advanced-Lossless in multiplexed
High-Speed Transfer mode:
v=0
o=atrac 2465317890 2465317890 IN IP4 service.example.com
s=AAL Multiplexed Streaming
c=IN IP4 192.0.2.1/127
t=3409539540 3409543140
m=audio 49200 RTP/AVP 96
a=rtpmap:96 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:96 baseLayer=128; blockLength=2048; channelID=2
a=maxptime:47
Example usage of ATRAC-Advanced-Lossless in multi-session
High-Speed Transfer mode. In this case, the base layer and the
enhancement layer stream are identified by L1 and L2 respectively,
and L2 depends on L1 in decoding.
v=0
o=atrac 2465317890 2465317890 IN IP4 service.example.com
s=AAL Multi Session Streaming
c=IN IP4 192.0.2.1/127
t=3409539540 3409543140
a=group:DDP L1 L2
m=audio 49200 RTP/AVP 96
a=rtpmap:96 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:96 baseLayer=128; blockLength=2048; channelID=2
a=maxptime:47
a=mid:L1
m=audio 49202 RTP/AVP 97
a=rtpmap:97 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:97 baseLayer=0; blockLength=2048; channelID=2
a=maxptime:47
a=mid:L2
a=depend:97 lay L1:96
Example usage of ATRAC-Advanced-Lossless in Standard mode:
m=audio 49200 RTP/AVP 99
a=rtpmap:99 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:99 baseLayer=0; blockLength=1024; channelID=2
a=maxptime:24
Hatanaka, et al. [Page 29]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
7.9 Example Offer-Answer Exchange
The following Offer/Answer example shows how a desire to stream
multi-channel content is turned down by the receiver, who answers
with only the ability to receive stereo content:
Offer:
m=audio 49170 RTP/AVP 98 99
a=rtpmap:98 ATRAC-X/44100/6
a=fmtp:98 baseLayer=320; channelID=5
a=rtpmap:99 ATRAC-X/44100/2
a=fmtp:99 baseLayer=160; channelID=2
Answer:
m=audio 49170 RTP/AVP 99
a=rtpmap:99 ATRAC-X/44100/2
a=fmtp:99 baseLayer=160; channelID=2
The following Offer/Answer example shows the receiver answering with
a selection of supported parameters:
Offer:
m=audio 49170 RTP/AVP 97 98 99
a=rtpmap:97 ATRAC-X/44100/2
a=fmtp:97 baseLayer=128; channelID=2
a=rtpmap:98 ATRAC-X/44100/6
a=fmtp:98 baseLayer=128; channelID=5
a=rtpmap:99 ATRAC-X/48000/6
a=fmtp:99 baseLayer=320; channelID=5
Answer:
m=audio 49170 RTP/AVP 97 98
a=rtpmap:97 ATRAC-X/44100/2
a=fmtp:97 baseLayer=128; channelID=2
a=rtpmap:98 ATRAC-X/44100/6
a=fmtp:98 baseLayer=128; channelID=5
The following Offer/Answer example shows an exchange in trying to
resolve using ATRAC-Advanced-Lossless. The offer contains three
options: multi-session High-Speed Transfer mode, multiplexed High-
Speed Transfer mode, and Standard mode.
Hatanaka, et al. [Page 30]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
Offer:
// Multi-session High-Speed Transfer mode, L1 and L2 are correspond to
the base layer and the enhancement layer respectively, and L2 depends
on L1 in decoding.
a=group:DDP L1 L2
m=audio 49200 RTP/AVP 96
a=rtpmap:96 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:96 baseLayer=132; blockLength=1024; channelID=2
a=maxptime:24
a=mid:L1
m=audio 49202 RTP/AVP 97
a=rtpmap:97 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:97 baseLayer=0; blockLength=2048; channelID=2
a=maxptime:24
a=mid:L2
a=depend:97 lay L1:96
// Multiplexed High-Speed Transfer mode
m=audio 49200 RTP/AVP 98
a=rtpmap:98 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:98 baseLayer=256; blockLength=2048; channelID=2
a=maxptime:47
// Standard mode
m=audio 49200 RTP/AVP 99
a=rtpmap:99 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:99 baseLayer=0; blockLength=2048; channelID=2
a=maxptime:47
Answer:
a=group:DDP L1 L2
m=audio 49200 RTP/AVP 94
a=rtpmap:94 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:94 baseLayer=132; blockLength=1024; channelID=2
a=maxptime:24
a=mid:L1
m=audio 49202 RTP/AVP 95
a=rtpmap:95 ATRAC-ADVANCED-LOSSLESS/44100/2
a=fmtp:95 baseLayer=0; blockLength=2048; channelID=2
a=maxptime:24
a=mid:L2
a=depend:95 lay L1:94
Hatanaka, et al. [Page 31]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
Note that payload format (encoding) names are commonly shown in
upper case. Media subtypes are commonly shown in lower case.
These names are case-insensitive in both places. Similarly,
parameter names are case-insensitive both in Media types and in
the default mapping to the SDP a=fmtp attribute.
8. IANA Considerations
Three new Media subtypes, for audio/ATRAC3, audio/ATRAC-X,
audio/ATRAC-ADVANCED-LOSSLESS are requested to be registered
(see Section 7).
9. Security Considerations
The payload format as described in this document is subject to the
security considerations defined in RFC3550 [1] and any applicable
profile, for example RFC 3551 [3]. Also the security of media type
registration MUST be taken into account as described in section 5 of
RFC 4855[6].
The payload for ATRAC family consists solely of compressed audio
data to be decoded and presented as sound, and the standard
specifications of ATRAC3, ATRAC-X and ATRAC Advanced Lossless[9][10]
[11] strictly define the bit stream syntax and the buffer model in
decoder side for each codec. So they can not carry "active content"
that could impose malicious side-effects upon the receiver, and
they does not cause any problem of illegal resource consumption in
receiver side, as far as the bit streams are conforming to their
standard specifications.
This payload format does not implement any security mechanisms of
its own. Confidentiality, integrity protection, and authentication
have to be provided by a mechanism external to this payload format,
e.g., SRTP RFC3711[13].
Hatanaka, et al. [Page 32]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
10. Considerations on Correct Decoding
10.1 Verification of the Packets
Verification of the received encoded audio packets MUST be performed
so as to ensure correct decoding of the packets. As a most primitive
implementation, the comparison of the packet size and payload length
can be taken into account. If the UDP packet length is longer than
the RTP packet length, the packet can be accepted, but the extra
bytes MUST be ignored. In case of receiving shorter UDP packet or
improperly encoded packets, the packets MUST be discarded.
10.2 Validity Checking of the Packets
Also validity checking of the received audio packets MUST be
performed. It can be carried out by decoding process, as ATRAC
format is designed so that the validity of data frames can be
determined by decoding algorithm. The required decoder response to
a malformed frame is to discard the malformed data and conceal the
errors in the audio output until a valid frame is detected and
decoded. This is expected to prevent crashes and other abnormal
decoder behavior in response to errors or attacks.
Hatanaka, et al. [Page 33]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
11. References
11.1 Normative References
[1] Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobsen,
"RTP: A Transport Protocol for Real-Time Applications",
RFC 3550, STD 64, July 2003.
[2] Handley, M. , V. Jacobson and C. Perkins, "SDP: Session
Description Protocol", RFC 4566, July 2006.
[3] Schulzrinne, H., "RTP Profile for Audio and Video Conferences
with Minimal Control", RFC 3551, STD 65, July 2003.
[4] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels, BCP 14", RFC 2119, March 1997.
[5] N. Freed, J. Klensin,
"Media Type Specifications and Registration Procedures",
RFC 4288, STD 64, March 2005.
[6] S. Casner,
"Media Type Registration of RTP Payload Formats",
RFC 4855, STD 64, July 2003.
[7] Camarillo, G., Holler, J., and H. Schulzrinne, "Grouping of
Media Lines in the Session Description Protocol (SDP)",
RFC 3388, March2002.
[8] Schierl, T., Wenger, S. "draft-ietf-mmusic-decoding-
dependency-04.txt", Internet draft, February 25 2008.
[9] ATRAC3 Standard Specification ver.1.1,
Sony Corporation, 2003.
[10] ATRAC-X Standard Specification ver.1.2,
Sony Corporation, 2004.
[11] ATRAC Advanced Lossless Standard Specification ver.1.1,
Sony Corporation, 2007.
ATRAC specifications[9-11] are provided for the ATRAC licensed
users. See https://datatracker.ietf.org/ipr/ for the details
of the license.
Hatanaka, et al. [Page 34]
INTERNET-DRAFT draft-ietf-avt-rtp-atrac-family-22.txt April, 2009
11.2 Informative References
[12] Perkins, C., Kouvelas, I., Hodon, O., Hardman, V., Handley, M.,
Bolot, J.C., Vega-Garcia, A. and Fosse-Parisis, S.,
"RTP Payload for Redundant Audio Data", RFC 2198,
September 1997.
[13] Baugher, M., Carrara, E., McGrew, D., Naslund, M., and Norrman,
"The Secure Real Time Transport Protocol", RFC 3711,
March 2004.
[14] Rosenberg, J. and Schulzrinne, "An Offer/Answer Model with the
Session Description Protocol (SDP)", RFC 3264, June 2002.
[15] Schulzrinne, H., Rao, and Lanphier, "Real Time Streaming
Protocol (RTSP)", RFC 2326, April 1998.
[16] Handley, M., Perkins, C. and Whelan, "Session Announcement
Protocol", RFC 2974, October 2000.
Authors' Addresses
Mitsuyuki Hatanaka
Sony Corporation, Japan
1-7-1 Konan
Minato-ku
Tokyo 108-0075
Japan
Jun Matsumoto
Sony Corporation, Japan
1-7-1 Konan
Minato-ku
Tokyo 108-0075
Japan
Email: actech@jp.sony.com
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Hatanaka, et al. [Page 35]